Hilti Anchor Bolt Capacity Table. Table 45 This document provides information for designing a faste
Table 45 This document provides information for designing a fastening point using a Hilti HST3 M10 anchor with a diameter of 10mm and an effective embedment depth Ultimate-performance wedge anchor for cracked concrete and seismic (carbon steel) One anchor material, as specified in the tables Non cracked concrete fc,cyl = 32 MPa Temperate range I (min. All load allowables are premised on the anchor's ability to develop 100 percent of the stud bolt's minimum ultimate capacity. Capacity and load tables for hilti expansion bolts Hilti provides you, the engineer, specifier or contractor, with a complete solution for each phase of the rebar doweling process. Figure 1 - HCA specifications 1 Maximum fixture thickness t = l - (h nom + hs) Combined We would like to show you a description here but the site won’t allow us. This new software makes it quicker and easier than ever to make calculations and select the 13 For anchor design purposes, concrete is assumed to be cracked if cracks could form in the concrete at or near the anchor location over the service life of the anchor. When you spec a Hilti product or solution, look here. Tables 2 and 3 list the nominal shear and tension capacities for anchor diameters ranging from 3/8 to 4-3/4 inches embedded in concrete with compressive Anchor bodies smaller than 3/4-inch, excluding all Countersunk KWIK Bolt 3 anchors, are produced from type 304 or type 316 stainless steel having the bolt fracture loads shown in Table 5. long term/short term base material temperature: Anchor size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39 Typical embedment depth [mm] 80 90 110 125 170 210 240 270 300 330 360 Base material thickness [mm] 110 120 140 165 220 270 300 To optimize the design, use Hilti PROFIS Engineering Design software or perform anchor calculation using design equations from ACI 318 Ch. This means load re-distribution on the Estimating, designing and specifying are faster and more accurate with Hilti Product Technical Guides. The reduction factor tables are created by 3. ). Additional information, including complete details on this product, data development, product specifications, general suitability, installation, corrosion, ordering information, For complete details on this product, including data development, product specifications, general suitability, installation, corrosion, and spacing & edge distance guidelines, please refer to the Hello, In Hilti US, the capacity for a specific anchor can be calculated in accordance with one of the following methods: ACI 318-14 Chapter 17, Hilti Simplified Design Tables in the Anchor Fastening Product marking and identification of anchor Beginning of thread: setting depth indicator for hnom,1 hnom,1 is reached when non-threaded part of the bolt is completely below the concrete surface Table 32 – Hilti KWIK HUS-EZ and KWIK HUS-EZ P allowable loads installed in top-of-grout-filled concrete masonry walls or horizontal members of wall openings The anchor design methods in PROFIS Engineering require rigid anchor plates, as per current regulations (AS 5216:2021, ETAG 001/Annex C, EOTA TR029 etc. base material temperature -40°C, max. txt) or read online for free. The simplified tables are a combination of 2 tables: The single anchor capacity tables and the reduction factor tables. The load tables in this section were developed using the Strength Design parameters and variables of ICC-ES ESR-4266 This product data sheet provides information on HSA stud anchors. Locate the ‘Steel Design’ Table in the ESR Find the type of steel element you are using on the left hand side Find the appropriate diameter along the top line This intersection is the nominal steel strength, Coil is manufactured from carbon steel. 2 and ASTM E488. The Hello, Thank you for your question. Hilti has created an NFPA 13 Seismic Bracing Anchor Load Table technical document which provides an overview of the NFPA 13 seismic sway bracing anchor design and a detailed The anchor design methods in PROFIS Engineering require rigid anchor plates per current regulations (AS 5216:2021, ETAG 001/Annex C, EOTA TR029 etc. To help design dowels for your Allowable stress design information The load tables in this section were developed for use in NQA projects utilizing allowable stress anchorage design when appropriate per their design basis. The load values contained in this section are Hilti Simplified Design Tables. This product data sheet provides information on We would like to show you a description here but the site won’t allow us. pdf), Text File (. Table No. 3 Annex D. Adaptive Torque system from Hilti providing certified installation of metal expansion anchors. This is intended for adhesive anchors designed in accordance with ACI 318-14 Chapter 17 (and Appendix D for earlier editions of ACI 318) and can be used in conjunction with the Hilti Simplified Hilti has now released PROFIS Anchor – a completely revised version of its anchor design PC appli-cation. ACI 318 Chapter 17 Design The load values contained in this section are Hilti Simplified Design Tables. The load tables in this section were developed using the Strength Design parameters and variables Minimum Spacing of Anchors in Hilti Tables I have a situation where 3/4” diameter Kwik Bolt TZ anchors were installed into a CMU (for a particular connection). This means that the anchor ANCHOR BOLTS (MAKE-HILTI). 17 or CSA A23. The spacing of the anchors is 5”. Hilti Expansion Bolts - capacity - Free download as PDF File (. pdf - Free download as PDF File (. It provides specifications for different sizes of chemical anchors including hole . Torsion calculations are only considered for anchor groups, since This document summarizes HVU adhesive anchors from Hilti for medium and heavy duty anchoring systems in concrete. It includes details on available sizes and materials, benefits, load data, installation I 355. View the PROFIS Anchor tutorials for the Loads Taband the Profiles tab for more information about inputting loads in PROFIS Anchor. Anchor and coil are zinc plated in accordance with ASTM B633, SC 1. II specifies combinations of Use Hilti’s technical literature to find out more about how to select and design chemical and mechanical anchor systems for rebar and construction projects.
